6d84795bc1
* Update ARM split keyboard docs * Update docs/serial_driver.md Co-authored-by: Nick Brassel <nick@tzarc.org> Co-authored-by: Nick Brassel <nick@tzarc.org>
90 lines
4.2 KiB
Markdown
90 lines
4.2 KiB
Markdown
# Converting a board to use the Proton C
|
|
|
|
Since the Proton C is a drop-in replacement for a Pro Micro we've made it easy to use. This page documents a handy automated process for converting keyboards, as well as documenting the manual process if you'd like to make use of Proton C features that aren't available on Pro Micros.
|
|
|
|
## Automatic Conversion
|
|
|
|
If a board currently supported in QMK uses a Pro Micro (or compatible board) and you want to use the Proton C, you can generate the firmware by appending `CONVERT_TO_PROTON_C=yes` (or `CTPC=yes`) to your make argument, like this:
|
|
|
|
make 40percentclub/mf68:default CTPC=yes
|
|
|
|
You can add the same argument to your keymap's `rules.mk`, which will accomplish the same thing.
|
|
|
|
This exposes the `CONVERT_TO_PROTON_C` flag that you can use in your code with `#ifdef`s, like this:
|
|
|
|
```c
|
|
#ifdef CONVERT_TO_PROTON_C
|
|
// Proton C code
|
|
#else
|
|
// Pro Micro code
|
|
#endif
|
|
```
|
|
|
|
If you get errors about `PORTB/DDRB`, etc not being defined, so you'll need to convert the keyboard's code to use the [GPIO Controls](internals_gpio_control.md) that will work for both ARM and AVR. This shouldn't affect the AVR builds at all.
|
|
|
|
The Proton C only has one on-board LED (C13), and by default, the TXLED (D5) is mapped to it. If you want the RXLED (B0) mapped to it instead, add this like to your `config.h`:
|
|
|
|
#define CONVERT_TO_PROTON_C_RXLED
|
|
|
|
## Feature Conversion
|
|
|
|
These are defaults based on what has been implemented for ARM boards.
|
|
|
|
| Feature | Notes |
|
|
|-------------------------------------|------------------------------------------------------------------------------------------------------------------|
|
|
| [Audio](feature_audio.md) | Enabled |
|
|
| [RGB Lighting](feature_rgblight.md) | Disabled |
|
|
| [Backlight](feature_backlight.md) | Forces [task driven PWM](feature_backlight.md#software-pwm-driver) until ARM can provide automatic configuration |
|
|
| USB Host (e.g. USB-USB converter) | Not supported (USB host code is AVR specific and is not currently supported on ARM) |
|
|
| [Split keyboards](feature_split_keyboard.md) | Partial - heavily dependent on enabled features |
|
|
|
|
## Manual Conversion
|
|
|
|
To use the Proton C natively, without having to specify `CTPC=yes`, you need to change the `MCU` line in `rules.mk`:
|
|
|
|
```
|
|
MCU = STM32F303
|
|
```
|
|
|
|
Remove these variables if they exist:
|
|
|
|
* `BOOTLOADER`
|
|
* `EXTRA_FLAGS`
|
|
|
|
Finally convert all pin assignments in `config.h` to the stm32 equivalents.
|
|
|
|
| Pro Micro Left | Proton C Left | | Proton C Right | Pro Micro Right |
|
|
|-----------|----------|-|----------|-----------|
|
|
| `D3` | `A9` | | 5v | RAW (5v) |
|
|
| `D2` | `A10` | | GND | GND |
|
|
| GND | GND | | FLASH | RESET |
|
|
| GND | GND | | 3.3v | VCC <sup>1</sup> |
|
|
| `D1` | `B7` | | `A2` | `F4` |
|
|
| `D0` | `B6` | | `A1` | `F5` |
|
|
| `D4` | `B5` | | `A0` | `F6` |
|
|
| `C6` | `B4` | | `B8` | `F7` |
|
|
| `D7` | `B3` | | `B13` | `B1` |
|
|
| `E6` | `B2` | | `B14` | `B3` |
|
|
| `B4` | `B1` | | `B15` | `B2` |
|
|
| `B5` | `B0` | | `B9` | `B6` |
|
|
| `B0` (RX LED) | `C13` <sup>2</sup> | | `C13` <sup>2</sup> | `D5` (TX LED) |
|
|
|
|
You can also make use of several new pins on the extended portion of the Proton C:
|
|
|
|
| Left | | Right |
|
|
|------|-|-------|
|
|
| `A4`<sup>3</sup> | | `B10` |
|
|
| `A5`<sup>4</sup> | | `B11` |
|
|
| `A6` | | `B12` |
|
|
| `A7` | | `A14`<sup>5</sup> (SWCLK) |
|
|
| `A8` | | `A13`<sup>5</sup> (SWDIO) |
|
|
| `A15` | | RESET<sup>6</sup> |
|
|
|
|
Notes:
|
|
|
|
1. On a Pro Micro VCC can be 3.3v or 5v.
|
|
2. A Proton C only has one onboard LED, not two like a Pro Micro. The Pro Micro has an RX LED on `D5` and a TX LED on `B0`.
|
|
3. `A4` is shared with the speaker.
|
|
4. `A5` is shared with the speaker.
|
|
5. `A13` and `A14` are used for hardware debugging (SWD). You can also use them for GPIO, but should use them last.
|
|
6. Short RESET to 3.3v (pull high) to reboot the MCU. This does not enter bootloader mode like a Pro Micro, it only resets the MCU.
|