204 lines
9.8 KiB
Text
204 lines
9.8 KiB
Text
Internal of HHKB pro
|
|
=====================
|
|
HHKB pro has MCU and some chips on separate two PCBs.
|
|
|
|
Controller PCB
|
|
--------------
|
|
M38K07M4 Renesas MCU with USB function
|
|
http://documentation.renesas.com/eng/products/mpumcu/rej03b0192_38k0ds.pdf
|
|
|
|
(HHKB_controller.jpg)
|
|
|
|
Keyswitch PCB
|
|
-------------
|
|
HC4051 Analog Multiplexer: select a row line.
|
|
http://www.ti.com/lit/ds/schs122j/schs122j.pdf
|
|
LS145 BCD Decoder: select a column line.
|
|
http://www.ti.com/lit/ds/symlink/sn74ls145.pdf
|
|
BU9831 Non-volatile electronic potentiometer: for calibration?
|
|
https://www.spezial.com/doc/rohm-a/bu9831.pdf
|
|
TP1683/4 Capacitive Sensing controller: no datasheet available.
|
|
|
|
(HHKB_keyswitch.jpg)
|
|
|
|
Topre original chip?
|
|
(HHKB_TP1684.jpg)
|
|
|
|
|
|
Connector Cable
|
|
---------------
|
|
Two PCBs are connected by 15 lines(13 in case of Pro2).
|
|
Vcc and GND use 3(2) lines each, other lines are for keyboard signaling.
|
|
|
|
HHKB connector lines:
|
|
JP Pro2 Pro Function Description TMK pin usage
|
|
--------------------------------------------------------------------------------------------
|
|
1 Vcc(5V) 5V
|
|
1 1 2 Vcc(5V) 5V
|
|
2 2 3 Vcc(5V) 5V
|
|
3 3 4 TP1684 ~KEY: Low(0) when key is pressed PD7 input(with pullup)
|
|
4 4 5 TP1684 HYS: High(1) when key is pressed PB7 output
|
|
5 5 6 HC4051 A(bit0)\ PB0 output
|
|
6 6 7 HC4051 B(bit1) > select row 0-7 PB1 output
|
|
7 7 8 HC4051 C(bit2)/ PB2 output
|
|
8 8 9 LS145 A(bit0)\ PB3 output
|
|
9 9 10 LS145 B(bit1) > select column 0-7 PB4 output
|
|
10 10 11 LS145 C(bit2)/ PB5 output
|
|
11 11 12 LS145 ~D(enable) Low(0) enables selected column PB6 output
|
|
12 12 13 GND GND
|
|
13 13 14 GND GND
|
|
15 GND
|
|
14 HC4051(Z2) ~Enable of Z2 row0-7 PC6
|
|
15 HC4051(Z3) ~Enable of Z3 row8-15 PC7
|
|
|
|
NOTE: Probably HYS changes threshold for upstroke and makes hysteresis in the result.
|
|
NOTE: HYS should be given High(1) when previous KEY state is Low(0).
|
|
NOTE: 1KOhm didn't work as pullup resistor on KEY. AVR internal pullup or 10KOhm resistor was OK.
|
|
NOTE: JP has two HC4051(Z2,Z3) and line 5, 6 and 7 are connected to both of them.
|
|
|
|
(HHKB_connector.jpg)
|
|
|
|
|
|
Keyswitch matrix
|
|
----------------
|
|
HHKB switch matrix is ghost-free and bounce-free.
|
|
|
|
Pro/Pro2(8x8):
|
|
COL 0 1 2 3 4 5 6 7
|
|
ROW ---------------------------------------------------------------
|
|
0| 2 q w s a z x c
|
|
1| 3 4 r e d f v b
|
|
2| 5 6 y t g h n _NONE_
|
|
3| 1 Esc Tab Control LShift LAlt LMeta Space
|
|
4| 7 8 u i k j m _NONE_
|
|
5| \ ` Delete Return Fn RShift RAlt RMeta
|
|
6| 9 0 o p ; l , _NONE_
|
|
7| - + ] [ ' / . _NONE_
|
|
|
|
|
|
JP(16x8):
|
|
COL 0 1 2 3 4 5 6 7
|
|
ROW ---------------------------------------------------------------
|
|
0| ESC TAB LFn LShift LCtrl
|
|
1| 4 E MuHKN C D
|
|
2| 3 W LAlt X S
|
|
3| 1 HHK
|
|
4|
|
|
5| 5 R V F
|
|
6| 2 Q LGui Z A
|
|
7| 6 T Space B G
|
|
8| 9 I Kana , K
|
|
9| 8 U Henkan M J
|
|
A| 7 Y N H
|
|
B| 0 O RAlt . L
|
|
C| BS Right RShift Enter
|
|
D| \ [ Down Up ]
|
|
E| - P RFn / ;
|
|
F| ~ @ Left Ro :
|
|
|
|
|
|
Matrix diagram:
|
|
|
|
Pro/Pro2:
|
|
+-------------------------+-+-+-+-+-+-+-+ Vcc
|
|
|bias control? - - - - - - - - ---
|
|
| 3.9K*8 R R R R R R R R |
|
|
+--------^+ +--------+ - - - - - - - - |
|
|
| 2| | HC4051 <0-------|-|-|-|-|-|-|-|--|R|-+
|
|
| |capa. | <1-------|-|-|-|-|-|-|-|--|R|-+
|
|
| TP1684 |sense | <2-------|-|-|-|-|-|-|-|--|R|-+
|
|
| 11<------| <3-------|-|-|-|-|-|-|-|--|R|-+
|
|
| | | <4-------|-|-|-|-|-|-|-|--|R|-+
|
|
| | | <5-------|-|-|-|-|-|-|-|--|R|-+
|
|
| <-+ | <6-------|-|-|-|-|-|-|-|--|R|-+
|
|
| 1 4 | | | <7-------|-|-|-|-|-|-|-|--|R|-+
|
|
+---V---^-+ | +-^-^-^--+ 0 1 2 3 4 5 6 7 33K*8
|
|
KEY HYS | A B C +-----------------+
|
|
| | +-^----+ | | | | LS145 |
|
|
Vcc | | |BU9831| | | | +-^--^--^--^------+
|
|
--- | | +------+ | | | A B C D +-------+
|
|
| | | | | | | | | | | |
|
|
1-3 4 5 6 7 8 9 10 11 12 13-15 Pro |
|
|
1-2 3 4 5 6 7 8 9 10 11 12-13 Pro2|
|
|
+--------------------------------------------------+ |
|
|
| connector | ---
|
|
+--------------------------------------------------+ GND
|
|
|
|
|
|
JP:
|
|
+-----------------------------+-+-+-+-+ Vcc
|
|
|bias control? - - - - - ---
|
|
| 3.9K*5 R R R R R |
|
|
+--------^+ +--------+ - - - - - |
|
|
| | | HC4051 <0-----------|-|-|-|-|----|R|-+
|
|
| |capa. | Z2 <1-----------|-|-|-|-|----|R|-+
|
|
| TP1684 |sense | <2-----------|-|-|-|-|----|R|-+
|
|
| <---+--| <3-----------|-|-|-|-|----|R|-+
|
|
| | | | <4-----------|-|-|-|-|----|R|-+
|
|
| | ~En| <5-----------|-|-|-|-|----|R|-+
|
|
| | +----> <6-----------|-|-|-|-|----|R|-+
|
|
| | | | | A B C <7-----------|-|-|-|-|----|R|-+
|
|
+---V---^-+ | | +-^-^-^--+ | | | | | |
|
|
KEY HYS | | | | | | | | | | |
|
|
| | | | +--------+ | | | | | |
|
|
| | | | | HC4051 <8-----------|-|-|-|-|----|R|-+
|
|
| | | | | Z3 <9-----------|-|-|-|-|----|R|-+
|
|
| | | +--| <A-----------|-|-|-|-|----|R|-+
|
|
| | | | <B-----------|-|-|-|-|----|R|-+
|
|
| | | | <C-----------|-|-|-|-|----|R|-+
|
|
| | | ~En| <D-----------|-|-|-|-|----|R|-+
|
|
| | | +-> <E-----------|-|-|-|-|----|R|-+
|
|
| | | | | A B C <F-----------|-|-|-|-|----|R|-+
|
|
| | | | +-^-^-^--+ 0 1 2 3 4 5 6 7 33K*8
|
|
| | | | | | | +-----------------+
|
|
| | | | | | | | LS145 |
|
|
Vcc | | | | | | | +-^--^--^--^------+
|
|
--- | | | | | | | A B C D +-------+
|
|
| | | | | | | | | | | | | |
|
|
1-2 3 4 14 15 5 6 7 8 9 10 11 12-13 |
|
|
+--------------------------------------------------+ |
|
|
| connector | ---
|
|
+--------------------------------------------------+ GND
|
|
|
|
|
|
Signals charts
|
|
--------------
|
|
While pressing space bar, watched HHKB Pro original controller signals by logic analyzer.
|
|
Row and column is looping between 0-7 each for selecting a key.
|
|
A key is scaned every about 15ms, so scan rate is 66Hz.
|
|
|
|
(HHKB_chart1.jpg)
|
|
|
|
Space bar locate at ROW:3 COL:7. A key is selected by HC4051(C,B,A) and LS145(C,B,A).
|
|
Key state can be read on TP1684(4/KEY) while asserting low on LS145(D).
|
|
|
|
(HHKB_chart2.jpg)
|
|
|
|
|
|
Signal of JP:
|
|
|
|
1) Select row
|
|
rowC ____~~~~____~~~~ 3.8/3.8ms(JP) 7.7/7.7ms(Pro) S2 of HC4051
|
|
rowB __~~__~~__~~__~~ 1.9/1.9ms(JP) 3.8/3.8ms(Pro) S1 of HC4051
|
|
rowA _~_~_~_~_~_~_~_~ 1.0/1.0ms(JP) 1.9/1.9ms(Pro) S0 of HC4051
|
|
0123456701234567 selected row(Pro)
|
|
0123456789ABCDEF selected row(JP)
|
|
rowEn0 ________~~~~~~~~ 7.7/7.7ms(JP only) ~Enable of Z2 HC4051(JP only)
|
|
rowEn1 ~~~~~~~~________ 7.7/7.7ms(JP only) ~Enable of Z3 HC4051(JP only)
|
|
|
|
2) Select column
|
|
colC ____~~~~____~~~~ 550/410us(JP) / us(Pro)
|
|
colB __~~__~~__~~__~~ 200/210us(JP) 450/460us(Pro)
|
|
colA _~_~_~_~_~_~_~_~ 100/110us(JP) 220/230us(Pro)
|
|
0123456701234567 selected column
|
|
|
|
3) Wait 5us after column select, then set prev, strobe colD to spit out key status and read it.
|
|
hys _~~~~_____ 20us if previous key state is low
|
|
colD ~~~__~~~~~ 10us strobe
|
|
key ~~~____~~~ 22us indicates current state of the key
|
|
|
|
NOTE: JP scans twice fast as Pro/Pro2 does. So Pro/Pro2 scans 8x8 matrix in 15.4ms while JP scans 16x8 in that time.
|
|
|
|
|
|
|
|
EOF
|